Minolta CF3102 Manual de Serviço Página 135
- Página / 298
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
FrameMaker Ver5.5E(PC) CF3102/CF2002 SWITCHES ON PWBs/TECH. REP. SETTINGS
02.06.05
S-2
(1) Initialize Procedure
1. Turn OFF the Power Switch.
2. With the circuit across pins of PJ2 closed, turn ON the Power Switch.
3. In about 5 sec., open the PJ2 circuit.
4. Check that the message “Initialize Completed” is displayed on the Touch Panel and
then touch “END.”
(2) Memory Clear Procedure
1. Turn OFF the Power Switch.
2. With the circuit across TP1 and TP3 closed, turn ON the Power Switch.
3. In about 5 sec., open the circuit across TP1 and TP3.
4. Check that the message “Memory Clear Completed” is displayed on the Touch Panel
and then touch “END.”
5. The following types of data are cleared.
• Utility mode: Input, User's Choice 1/2
• Tech. Rep. mode: System Input, Administrator # Input
• Security mode: Counter Setting
• Touch Panel Adj.
NOTES
• If the copier exhibits an erratic display or operation, unplug and plug in the power cord,
turn OFF and ON the Power Switch, and then perform the following procedures in this
order: Initialize
→ Memory Clear.
• Do not perform Memory Clear casually, as it clears the types of data mentioned above. If
Memory Clear has been performed, be sure to make settings for the functions that have
been cleared once again.
- CF2002/CF3102 1
- 1-1. Warning 3
- 1-2. Caution 5
- 1-4. Other Precautions 8
- 1-5. Precautions for Service 8
- 01.11.15 10
- 02.07.01 12
- CONTENTS 13
- MAINTENANCE 13
- DIS/REASSEMBLY, ADJUSTMENT 14
- 02.07.02 15
- TROUBLESHOOTING 16
- 02.06.26 21
- 1. SPECIFICATION 22
- 2-1. Installation Site 25
- 2-2. Power Source 25
- 2-3. Grounding 25
- 3. PRECAUTIONS FOR USE 26
- 4. HANDLING OF CONSUMABLES 27
- 5. OTHER PRECAUTIONS 28
- 6. LED RADIATION SAFETY 28
- 7. SYSTEM OPTIONS 29
- 1. MAINTENANCE SCHEDULE 31
- → “Counter” → “Life” 35
- →”Counter” →”Life” 38
- → “Counter”→”Life” 45
- 3. Replacing the Units 48
- → “Gradation Adjust” 52
- DIS/REASSEMBLY 58
- ADJUSTMENT 58
- 1. SERVICE INSTRUCTIONS 59
- 2. DISASSEMBLY/REASSEMBLY 61
- → Remove 11 screws and 63
- → Remove the Scanner 63
- → Remove five screws and 63
- 8. Remove two screws 69
- 2-3. Removal of Units 74
- 3. ADJUSTMENTS 100
- 3-2. MECHANICAL ADJUSTMENT 101
- 02.06.010 102
- → 0 → 0 → Stop → 0 → 1 103
- × 17” plain paper 104
- → “PRT Area” → “Top Margin.” 104
- → “PRT Area” → “Left Margin.” 106
- → “Lattice Pattern.” 108
- → “PRT Area” → “Zoom for FD.” 108
- → “Color Shift Correction.” 109
- → “LPH Pattern.” 112
- → “LPH Chip Adjust.” 112
- → “PRT Max Density.” 114
- → “PRT Highlight.” 115
- → “ATDC Level Setting.” 117
- → “AE Adjust.” 118
- → “2nd Transfer Adjust.” 119
- → “Fuser Temp.” 120
- → “Fuser Speed.” 121
- → 0 → Stop → 3 122
- → “IR Area.” 123
- → “Org. Detect Sensor.” 127
- 4. OTHER ADJUSTMENTS 128
- 4-3. FLASH MEMORY 130
- SWITCHES ON PWBs 133
- TECH. REP. SETTINGS 133
- 1-1. PWB Location 134
- → Memory Clear 135
- 02.06.05 136
- 2. UTILITY MODE 137
- 457mmor12x 144
- × 17, or A4C or 8-1/2 × 11 146
- 3. TECH. REP. MODE 149
- ± 0.5 mm 153
- ± 1.0 mm 154
- ± 0.2 mm 154
- → Memory,”“Memory 158
- → PRT,” or both 158
- °C increments 166
- °Cin1°C increments 166
- ±100 for R, G, and B 167
- ±90 for R and 167
- ±50 for G 167
- ∗” is displayed beside the 168
- × 11” length 172
- × 17” paper on the 174
- 4. SECURITY MODE 175
- × 17, and Legal 176
- 1. INTRODUCTION 179
- (3) Solenoid 180
- (4) Clutch 180
- (5) Motor 181
- 1-2. I/O CHECK 182
- (2) I/O Check List 183
- <I/O Check Screens> 183
- <I/O Check List> 184
- 02.06.13 185
- See the FN-116 service manual 186
- (Finisher) 186
- See the FN-8 service manual 187
- 2. PAPER MISFEED 190
- 2-1. Initial Check Items 190
- 2-2. Misfeed Display 191
- 3. MALFUNCTIONS 208
- → “Peripheral 234
- → “Memory/ 236
- → “Memory 236
- →”IR →Memory” 236
- →”Memory 237
- 4. IMAGE QUALITY PROBLEMS 249
- °C increments) 250
- 4-3. Initial Check Items 251
- 4 colors 252
- Mono color 252
- → Left Image 253
- →Top Image 254
- →Change bushing 258
- →Change Scanner Motor 258
- →Change Scanner Assy 262
- →Change CCD Unit 262
- →Change Image Transfer 266
- →Change LPH Assy 266
- →Change High Voltage Unit 268
- →PRT Max 271
- →PRT High 271
- → Level His 271
- → Table # 273
- →Change LPH Unit 277
- →Change PIC Board 278
- →Change LED Drive Board 278
- 94 mm94 mm 281
- →Change Fusing Unit 293
- <Typical Faulty Images> 294
Manuais e produtos relacionados com Impressora multifunções Minolta CF3102
(188 páginas)
Impressora multifunções Minolta EP1085 Manual de Serviço
(193 páginas)
(193 páginas)
Impressora multifunções Minolta 5430 Guia do Utilizador
(114 páginas)
(114 páginas)
Impressora multifunções Minolta EPI 054 Especificações
(339 páginas)
(339 páginas)
Impressora multifunções Minolta Di450 Manual de Serviço
(271 páginas)
(271 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais